DIY Modern Wooden Toy Box with Lid: A Step-by-Step Tutorial

DIY Modern Wooden Toy Box with Lid: A Step-by-Step Tutorial

As summertime techniques, my spring fever Simplify existence instincts kick into complete equipment. This includes de-junking and de-cluttering my whole house, even (to my little ones dismay) the toys. on the way to make the transition sense smoother and much less painful in transferring from more to less, I idea a beautiful toy field might do the trick. And, wouldnt you know it? It did. And we havent even formally crammed it but. #momwin

This DIY wood toy box feels both classic and modern on the equal time. It also would possibly appear intimidating as a assignment to begin, but you and a building partner certainly can knock out the development of it in half of a day if youve were given all of your wooden reduce to start with. Youre going to like it. agree with me.

be aware: it is imperative with any wood constructing assignment which you take all necessary safety precautions; work on a degree and smooth floor; measure and cut precisely, and test for square regularly that allows you to ensure the nice stop product.

materials wished:

start by means of sanding the whole thing. this could experience tedious when youre excited to get constructing, but accept as true with me. Its a good deal faster, less complicated, and better for the stop product to sand now than after the toy field is assembled.

Youll begin by constructing your side panels. Take a 12x12 plywood square and decide which facet will face the indoors of your toy box. area the grain going for walks sideways, then measure three in from the corners on the two facets (on the access/exit points of the grain). Youre marking the pocket hollow placement for the facet panel to connect to the legs here.

Following instructions, installation your loved one Kreg jig at the three/four intensity mark.

Drill your 4 pocket holes (two in step with aspect).

Your 12x12 square now seems like this.

subsequent, measure for 2 or 3 pocket holes on the pinnacle and bottom ends of your rectangular (use the photograph for size reference). those holes will attach the pinnacle and backside inset strips onto your facet panel. Repeat those steps for the opposite side panel.

for your 12x32 rectangle, determine which facet you need facing inward on your toy box. measure and mark 3 in from the top and bottom corners on both ends. Drill those four holes ( in keeping with give up). Then degree and mark five pocket holes on the pinnacle and bottom ends. (I didnt do the mathematics flawlessly, so ill let you do your own math the holes must ideally be spaced 6-8 apart.)

Your piece must now appear to be this. Repeat for the opposite rectangle.

Its now time to grab your 1×3 and 1×2 strips, consisting of now not just the 12 however also the thirteen lengths. The 12 1×3 strips will cross at the top (as in, close to the lid) of your plywood panels, the 1×2 strips will pass on the bottom (as in, near the floor) of your plywood panels. The 13 strips will pass onto the bottom of your toy field to help the container floor. (more on the ones later.)

Drill holes into every stop of your 1×three portions and one hole into every end of your 1×2 portions.

Repeat for the longer (32) strips as nicely.

We now need to prepare the front top strip (one in every of your 32 1x3s) for slicing out the finger preserve. From every (facet) end, measure and mark the 4 and 5 spots alongside the pinnacle (near the lid) cease.

Use a rectangular at your 5 marking to region a new five factor this is 1-three/four up from what will be the bottom (faraway from the lid) stop. Now draw a line from the 4 factor at the top to the brand new five factor. try this from each sides of your wooden strip.

Use a instantly edge to attract all of the traces you want to guide your jigsaw.

Use a jigsaw to make your reduce-out.

when you have a rather wide nook like this, actually curve your jigsaw around the corner to your first skip. You have to still be able to see the pencil marks at the nook factor.

whilst the principle piece is reduce out, come again together with your jigsaw and, coming in from each aspects of the nook, sharpen up that corner angle. Repeat on both facets.

Your finger maintain must appearance some thing like this.

move ahead and sand your sparkling cuts.

With the whole lot geared up with pocket holes, its time to gather your field! I advise having people and a flat and stage work floor to make this process less difficult. Run a bead of wood glue along the bottom of a 1×three 12 strip.

be part of the glue aspect with the pinnacle end of your facet A plywood. The pocket hollow sides should be flush. (Tip: Use different wooden portions beneath to make it flush; as in, stick a bit of half″ plywood under the 1×three strip that youve glued and a 1×three strip under the plywood youre gluing to. This creates a flat surface for you wherein the pocket holes connect.) ensure the edges are flush and all pocket holes are visible.

clamp in location, then use 1 pocket screws to attach.

Wipe away any extra glue. (make sure to wipe on the front and back aspects, and remember that if youre staining your toy container, stain wont take to attach so make sure that its all the way wiped off.)

Repeat this process for a 12 strip of one×2 on the opposite (bottom) stop of your facet A. Then repeat for facet B.

I assume the most beautiful aspect of this easy, contemporary toy field is the insets anywhere. when the pocket hole sides are flush, the opposite aspect of your panels could have that fantastic 3D wooden detailing. It looks very high-give up.

Repeat this precise technique for the square panels to create your front and back panels.

make sure youre checking for glue squeezing out on both the indoors and exterior aspects of your panels. Its clean to finish the pocket screwing and flow on without checking the other facet, however this would be a mistake, because glue will likely be squeezing out on that facet as properly.

Its now time to assemble the container by using attaching all the panels for your field legs, which are the 18-1/2 lengthy 2×2 forums. clutch aspect A and run a bead of glue along the aspect. Set the side A panel, glue side down, onto a 2×2 leg with the top ends flush.

The inside (pocket hole facet) of your side panel must be positioned half″ faraway from the corner edge of your 2×2 publish. whilst the panel is placed exactly, attach with 1-1/four pocket screws.

Wipe away excess glue. Repeat for the opposite leg on this panel.

With each 2×2 legs connected, the interior of your side A panel will appear to be this.

by way of positioning your side panel 1/2 away from the nook edge of your 2×2 leg, it offers the outside of your facet panel strips a beautiful 1/4″ inset. Repeat this technique for side B.

Now its time to attach the front and back square panels to the leg posts. Glue alongside one aspect of your panel.

Align the panel onto the leg (retaining it half″ in from the edge of the leg put up, top flush), and fix with 1-1/4 pocket screws.

Its starting to take form!

Repeat the attachment steps with the the front panel.

Lay your aspect B panel, pocket holes dealing with upward, on your flat, clean paintings floor. Run beads of glue alongside the open ends of your front and back panels, then have a helper flip the U-fashioned front/aspect A/back piece over and location the glued ends onto the aspect B legs. Have them hold the box in region at the same time as you align exactly and attach each ends with pocket screws.

Ta-da! A container.

That finger keep offers it such a pleasing touch. As do the insets; theyre diffused but so elegant.

Time to build the container ground. flip your container the other way up and place on a easy, degree floor.

place a thirteen 1×three strip inside the middle of the container, with the pocket holes facing you.

Use a rectangular to make sure its, nicely, rectangular. Then use 1 pocket screws to attach the 13 strip to the container back and front strips.

Repeat for the opposite two 13 1×3 strips. Your base guide is now prepared for the box floor.

measure 5/eight from the corners of your 13x33 plywood rectangle.

consider the way you left 1/2″ from the corner aspect of every leg whilst you attached your facet panels? nicely want to reduce out that part from the 4 corners of your toy field floor so it suits.

Use a jigsaw to cut them out.

Theyll appear like this.

Sand some thing which could need it before you lay the floor in the field.

With the smoothest side going through upward, slide your ground rectangle into your container. It ought to be comfortable however not loopy tight.

To make sure degree, recollect placing a small piece of scrap wooden at each corner and hammering downward. This enables the ground to settle absolutely. you may use 1 screws thru the bottom of your base guide forums if you sense its essential to hold your ground in place; this one, but, changed into snug sufficient that we didnt want to comfy it.

Congratulations! The building of your field is now complete, unless you want a lid. Even then, its time to pause and finish the box the way you need it. Unwrap your venture panel; this may be the top (lid) of your field.

Its a beautiful thing that the assignment panel is bought in the precise size for your wishes, isnt it?

deliver the lid a mild sanding.

finish your container how you need it. I chose to use paints we already had, with a bit peek-a-boo evaluation on the internal (of each the box and the lid). My daughter, whom this container is for, glimpsed the container and lid drying in the storage and exclaimed, Ah! i love it! It looks like an elephant! So. If youre after the appearance of an elephant, I propose faded purple internal some kind of smooth gray.

once your box is completed (e.g., stained or painted and thoroughly dry), all you need to do is connect the lid. this is so simple with these torsion hinges (bought for this task from this supplier). you may location the hinges anywhere you want, but ill show you the way I did it. sense unfastened to adjust as you want. on the inside/under facet of your lid, alongside the back stop, measure five in from the edges and 1-7/eight in from the returned end. this could no longer make the again of the lid flush with the again of the toy box; as an alternative, it'll be inset a touch bit, which evens out the overlap of the the front end of the lid on the toy container and, in my opinion, looks better and greater balanced. Mark this point, and draw a few light pencil traces.

Align the outdoor fringe of your hinge with your strains. Double take a look at to make certain it's miles flawlessly parallel together with your lid and is aligned.

Your hinge comes with 1 screws and different 3/4 screws. select the three/4″ screws for this task.

secure the hinge to the underside of your lid. Repeat for the alternative hinge.

Now slide the hinges onto the returned panel of your toy container. center the lid.

For this next job, youll need to pick out the two 1 screws.

Double-checking that the lid is, certainly, focused in your box, connect the hinge to the lower back panel.

Then, the usage of 3/four″ screws, connect the front facet of your hinge base to the back panel as well. Repeat for the alternative hinge.

Open your box lid. it works!

Now allow cross of your field lid. It stays in place! Thats the beauty of torsion hinges, particularly for a toy field wherein young youngsters may be the use of it. those hinges are greater costly, but they are well worth it to preserve little arms from getting smashed and the box lid from slamming again and again and over and over you get the concept.

Optionally, you may region rubber or felt pads at the lid or at the pinnacle of your the front leg posts to shield the front stop of your lid while its down.

The give up. Your personal lovely DIY modern-day timber toy container, which may additionally or might not appear like an elephant.

The 3 levels of inset on all panels of this toy box genuinely set it aside as some thing unique.

As does that lengthy, simple, and modern finger slot.

Open it up, andPINK! Very exciting round right here.

you may have noticed that I didnt do some thing to cover up the pocket holes. For me, it wasnt well worth it. if you sense otherwise, but, feel unfastened to accomplish that. Fill them with putty, sand them down, and theyll virtually disappear while you paint.

i really like when capability surely blends with form, and those hinges in a nickel end actually do this for this toy field.

The lids staying energy is a lifesaver.

you may additionally select to connect a type of protect (with 1×3 strips) along the pinnacle sides and back of your lid for a more craftsman look.

because, in my house as a minimum, this field could be used as a play bench as tons as a field, I selected to hold the pinnacle of the lid perfectly flat.

i really like a evaluation color on the interior. Even in case you wanted white on the outdoor of your toy field to in shape your mild-and-ethereal fashion, jazz it up with a shiny cobalt or fuchsia or something interior. So amusing!

 

Heres the lid on its way down, even though it absolutely should dangle out in this awkwardly not-up-no longer-down position for hours. Days, probably.

And, closed. i hope you discover this tutorial useful, and that in case you use it to construct your very own DIY present day toy field youre completely pleased with the result.

glad DIYing!

Source: here

Leave a comment